|
|
| |
|
|
Improving part consistency with CNC tube benders-管材展-鋼管展-2024第二十四屆廣州國際管材及管材加工設備展覽會－巨浪展覽-The 24th China(Guangzhou)Int'l Tube & Pipe Expo
11/20/2023 管材展-鋼管展-steel tube expo-pipe expo-pipe exhibition |
--------------------------------------------------------------------------------------------------------------- |
|
When production parts coming off CNC tube benders show variations, the natural reaction is to think there are problems with the machine or bend tooling.
While this sometimes is the case, variations just as often are caused by other factors. Following are a few common problems and things to check if you are not getting consistently good bends.
Length Variations
Length varies on the first straight, but all the other legs and the last straight length are consistent. Make sure your cut lengths are consistent. While this seems obvious, tube fabricators often struggle to get parts consistently within tolerance in their gauges because the variation in cut length exceeds the allowable variation in leg length.
Length varies in the first and last straight. Ensure that your load position is consistent and straight. A tube that is loaded into the collet at an angle (usually sagging down) typically will be lifted into a straight position when the collet closes so that it looks fine before bending starts.
However, imagine how the edge of the tube abuts the stops in the collet if it is sagging down: The bottom edge of the tube may contact the stop, but the top edge will not. When the collet closes and the tube is lifted, either the top has to move back some while the tube is lifting, or the bottom will have to come forward.
There’s an equal chance that the bottom will move forward, the top will move back, or a little of both. Because the relative position of the tube is moving forward and backward but the machine is moving to the same positions, both the first and last legs are affected but the lengths between bends are not.
Last leg length varies, but all other lengths are consistent. Watch to see if the clamp slips on the tube as bending starts and progresses. While clamp slip can cause all sorts of issues, it is entirely possible for the clamp to slip a little during the bend and cause no obvious issues with the quality of the bend.
However, when the clamp slips on the tube, less of the straight length is consumed. After bending, the carriage still correctly positions the tube between the two tangent points, which means that the change will show up in the last straight length. Because the amount the clamp slips will not be consistent, the last straight length also will not be consistent.
Leg lengths are inconsistent through the part. Watch if the tube slips in the collet. If the tube is being pulled slightly forward out of the collet during bending, it may get pushed back into the collet when the carriage pushes the tube out of the bend die. Similar to clamp slip, collet slip may not be very consistent, so it will seem like the leg lengths are constantly changing.
Rotation Variations
Rotations are consistent on the first couple of bends but vary on later bends. Watch for the tube to spin in the collet. As a part progresses through bending, it often gets farther and farther from the centerline of the tube. The farther away the first end of the tube gets away from center, the more leverage it has against the collet. As the rotation starts, more and more inertia must be overcome both to start and stop the rotation.
Rotations are inconsistent on a single bend. Look for interference from the part catching some part of the tooling or machine.
Bend Quality Issues
The outside of the bend is flattening. If using a mandrel, check the mandrel’s nose-to-tangent position. Depending on the type of mandrel, the nose should almost always be slightly in front of the tangent line of the bend die. This rounds the outside radius of the tube, though it naturally wants to flatten.
Check the pressure die assist (PDA) speed. If the PDA speed is set too low, it will add drag along the outside radius of the bend and may cause the tube to flatten.
The outside radius of the bend has a hump. Check the position of the mandrel. It is likely too far forward.
Wrinkles are forming inconsistently. Clamp slippage is the most common cause of inconsistent wrinkles. Because the amount that the clamp slips generally won’t be consistent, you may find that while several parts will be OK, a couple will have one or two bends that wrinkle a little. Or, you might have one bend that suddenly wrinkles a lot, but every other bend is OK.
When the clamp starts to slip, eventually the action changes from a bend to more of a fold. That’s when wrinkles start to form.
Additional Factors to Check
Amount of mandrel lubricant. As the tube forms, excess oil or gel lubricant can get trapped and create inconsistent voids between the tube wall and mandrel that otherwise would not be there.
Collet slip/carriage speed when bending with carriage boost. If your part requires carriage boost but the carriage speed is set too low, it may pull the tube forward slightly at the end of a bend. On the next bend, as the tube is drawn around the die, the carriage is unable to help the tube around because the tube slips back momentarily to its original position against the stop.
Weld seam. Confirm that tube is always loaded with the weld seam in the same location.
Pressure die pressure. A lot of issues, including wrinkles, can often be masked by adding pressure die pressure. However, add too much pressure and the PDA may not be able to travel forward with the tube, which then causes clamps to slip, which in turn causes wrinkles.
Too much pressure also can harm the machine and wear out consumables prematurely. Insufficient pressure also can cause wrinkles.
管材展-鋼管展-2024第二十四屆廣州國際管材及管材加工設備展覽會－巨浪展覽-The 24th China(Guangzhou)Int''l Tube & Pipe Expo
2024管材展，2024管材展會，廣州管材展，中國管材展會，2024廣州管材展，2024廣州管材展會，2024鋼管展，2024鋼管展會，2024鋼管展覽會，2024管件展，2024管件展會，2024管件展覽會，中國鋼管展會，中國管件展，2024管材加工展，2024管材加工展覽會，2024管材設備展會，2024鋼管設備展，2024管件設備展會，廣東管材展，廣東管材展會，2024廣東鋼管展，廣東鋼管展會，2024管材博覽會，2024鋼管博覽會，2024管件博覽會-pipe Industry Exhibition,pipe expo, 2024 pipe exhibition, 2024 pipe expo, China pipe exhibition, China pipe expo,pipe Industry event,pipe event, 2024 pipe event, 2024 pipe event, China pipe event, China pipe event,tube Industry Exhibition,tube expo, 2024 tube exhibition, 2024 tube expo, China tube exhibition, China tube expo,-tube Industry event,tube event, 2024 tube event, 2024 tube event, China tube event, China tube event
|
|
|
|
|
